OPERATING INSTRUCTIONSKP96 / KP97 SERIES KEYPANELSVERSION 8.3GWITH EKP96 / EKP97 EXPANSION PANELSAND LCP-100A LEVEL CONTROL PANELADAM™, ADAM™CS, AND Z
3.3.1.1 Keypanel IdentificationFUNC__DISPLAY__1This sequence displays the panel number of thekeypanel in the incoming messages window forabout 2 secon
additional expansion panels are connected, the setup pages for these will also be displayed using the same format.3.3.1.5 Test ModeFUNC__DISPLAY__0Whe
☞Tap CLR at any time to return to the normal incoming messages window display.3.4 ASSIGNING SETUP PAGESEach keypanel has 4 setup pages, and each setup
2. Select setup page 1-4 (4 in this example).3. Tap the PGM key.4. On the desired keypanel or expansion panel, press any talk or listen key. If the pa
3.5 PROGRAMMING TALK AND LISTEN KEYS3.5.1 GENERALThere are three methods to program talk and listen keys. These methods are summarized below and expla
2. If the keypanel, belt pack etc. that you want to assign to a key is located in a remote intercom system, enterthe intercom system number (7 for exa
3.5.2.2 Assigning a Party Line to a KeyA party line is a group of intercom stations that can always talk and/or listen to each other. Party lines are
• If a key will not accept an assignment, the party line that you are trying to assign may have been restricted (notenabled) by the intercom system co
tap 1 for Auto Listen, or...tap 2 for Auto Follow, or...tap 3 for Auto Mute, or...tap 4 for Auto Reciprocal, or...tap 5 for All Call.3. After selectin
☞If a key will not accept an assignment, the special function that you are trying to assign may have beenrestricted (not enabled) by the intercom syst
PROPRIETARY NOTICECOPYRIGHT NOTICEUNPACKING AND INSPECTIONWARRANTY INFORMATIONCUSTOMER SUPPORTRETURN SHIPPING INSTRUCTIONSPROCEDURE FOR RETURNSSHIPPIN
4. Enter the special list number (4 in this example).☞If the special list is in a remote intercom system, you must alwaysenter 2 digits by adding a le
2. Tap the IFB key.3. If the IFB is located in a remote intercom system, enter the intercom system number (5 in this example). Oth-erwise, skip to ste
3.5.2.6 Assigning an ISO to a KeyISO is a special type of communication used with party lines that have been setup using the intercom system’sparty li
5. Tap the PGM key.6. Press a talk key.The name of the ISO will appear in the alpha-numeric display above that talk key (on key-panels so equipped).☞I
☞Intercom system numbers are the numbers that appear in the “Icm” column in CStrunkwhen you select “Names” or “Setup” from the Intercoms menu.4. Enter
LEVEL 1: PANEL 45LEVEL 2: RELAY 5If the keypanel has alpha-numeric displays, the level 2 key assignment willdisplay briefly after the talk key is pres
2. Press the talk or listen key to which the call is to be copied.If a talk key is pressed, the name of the key assignment that you are copying will a
5. Repeat the steps to assign additional keys.☞If a key will not accept an assignment, the destination (intercom port, party line etc.) that you are t
☞The following abbreviations are used for types of communication:P-P Point-to-PointPL Party LineIFB IFBSPCL Special ListRLY RelayISO ISO4. When the de
a. Tap COPY CWb. Press the talk or listen key you want to copy to.If a talk key is pressed, the name of the key assignment that you are copying will a
KP96/KP97 Keypanel Operation Manual, Ver. 8.3G 3Table of ContentsINTRODUCTION ················································5DESCRIPTION OF USER CON
3. Tap the key to be cleared. This can be either a talk or listen key.☞If a key will not clear, restrictions may have been imposed using the intercom
3.5.6 ACTIVATING THE TONE GENERATORYou can check a keypanel’s audio send and receive paths to and from the matrix using the built-in tone generator.To
4 KP96/KP97 Keypanel Operation Manual, Ver. 8.3GList of FiguresKP96 / KP97 Keypanels ·············································1EKP96 / EKP97 Expan
1 INTRODUCTIONThis manual describes the operating procedures for the KP96/KP97 keypanels when used in an ADAM, ADAM CS,or Zeus Intercom System. The op
2 DESCRIPTION OF USER CONTROLS AND FEATURES(See Figure 1 for numbered callouts)1. Designation Strip Holder: A strip can be inserted here to identify t
2.1 BASIC KEYPANEL OPERATION2.1.1 POWER SWITCHA power switch is located on the back of each keypanel, expansion panel, and level control panel next to
2. In some cases you may not be able to hear the person, party line etc. to whom you are talking. In such cases,tap the listen key above the talk key.
3 ADVANCED OPERATIONS3.1 GENERALThe intercom system’s configuration computer and software are the primary tools for creating and saving inter-com syst
Comments to this Manuals